Pick it up today to repair or complete your Ithaca Model 49 Lever Action 22 Caliber Rifle. It’s in good condition all around with no major damage present no deep cuts, gouges, or rust pitting however, some of its finish has deteriorated. They were not noted for keeping pins and extractors in place as the receivers would weaken around the pins because of the soft pot metal.īE SURE TO CHECK OUT & FOLLOW MY INSTAGRAM FEEDĬONNECT WITH THE 1895GUNNER. You are considering a vintage Ithaca 49 Ejector Trip. Notes: The receivers were made of a pot metal type steel and the finish on the receivers was primarily a paint type finish.This is the repeater model 49 Saddle Gun lever action rifle in.22 rifles with the adjustable buttplate, the disassembly book referenced above and the owner's manual available online describe an incorrect procedure for removing the buttplate.Manufacturing details of the Ithaca Model 49R One footnote: If you should ever get one of the old Daisy. Ithaca Model 72 Tang Screw Lock Washer 5.00. Ithaca Model 72 Tube Carrier Lever Plunger 5.00. The Model 37 has many different versions, like Featherlight. Actually, the gun still fired with the broken firing pin, but I replaced it anyway. Ithaca Model 49 Parts 4 Ithaca Model 72 Saddlegun Parts 4 Products search. It is a pump-action shotgun that loads and ejects shotshells from the bottom of the gun. m49 m-49 lever action 22 22lr 18' no reserve. ![]() Removing and replacing the broken firing pin was easy compared to a complete teardown. 49 22 s/l/lr single shot falling block lever action rifle 11-17-228 02/06 18 inch ' barrel sold location: pittsburgh, pa 15237 sold date: 12:00:00 am: 305.00 - used.22 lr model 49 saddlegun ithaca gun co. Found one on ebay that was cheaper than Numrich. I used a chamber reamer to cure the extraction problem, reassembled, and now it works great.īTW, when I took it apart, I discovered that the firing pin was broken. Using the book you mentioned (love that book :t), I tore the gun completely down, even removing the barrel from the receiver. ![]() I tried just cleaning it, especially the chamber, but the extraction/ejection problems persisted. I also just recently got a nice walnut-stocked 49 (my first one.) The GS proprietor said that it was a little hard on extraction. ITHACA MODEL 49R LIFTER Vintage Original Rare Parts BEST DEALS ON EBAY OFFERS 25.53. To reassemble, be sure that you replace the plunger that is flat on both ends first, then the spring, then the other plunger with the rounded end down. Anyway, I have ordered a firing pin from Numrich and will take it to the local gunsmith as soon as the part arrives. NOTE: All items are used unless otherwise indicated. Lift the bolt out carefully so as not to lose the firing pin spring and the small pin that retains the firing pin. And, BTW, a friend on this forum sent me a link to an article about the Model 49 and that particular one used as information for the article shot a 7/16 inch group at 25 yds with the open sights. ![]() With these out, the large pin that holds the bolt can be pushed out toward either side. These must be removed and may take some tapping with a rubber hammer to get them out. These parts are intended to replace broken or missing parts from a similar make, model and vintage. Second, there are two plungers and a spring in the teardrop-shaped protrusion on the bottom of the bolt. This auction includes only the gun repair parts shown. The book you reference has good directions on this gun, although I can simplify somewhat the steps you need to replace the firing pin.įirst, drive out from left to right the pin that holds the lever and remove the lever downward. Replacing the firing pin is a piece of cake.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |